Dear ok1vpz, this is the mods.dk newsletter for articles and manuals.
In this Edition, you will find a list of all the new & updated articles on our site, and below you find a list of new files in the manuals section in the last months..
Created: 18 Mar 2018 Alinco DR-735 | |
Subject: MARS/CAP mod for Alinco DR-735T | |
Remove case cover from bottom and locate the usual blue wire loop. cut and tape/heat shrink the ends. reassemble cover. Do a full reset (will wipe memories) Turn on the radio by pressing PWR key whi... Click here to view the article. |
Created: 21 Mar 2018 Alinco DJ-MD40 | |
Subject: Override programming password on Alinco DJ-MD40 | |
To override the programming password, use windows Notepad to open Program Files (x86)AlincoMD_40_CPS_V1.07settings.ini The full folder address will probably be C:Program Files (x86)AlincoMD_40_CPS_V1... Click here to view the article. |
Created: 09 Mar 2018 Heathkit TT-1 | |
Subject: This paper (VR-005A) is an upgrade to the original paper VR-005 with corrections and improvements fo | |
This paper (VR-005A) is an upgrade to the original paper VR-005 (written in 2013), which was a lengthy paper documenting modernizations and improvements to the Heathkit TT-1A tube tester. This r... Click here to view the article. |
Created: 18 Jun 2018 Heathkit SB-201 | |
Subject: End to end RF Linear mods for SB-201 | |
This document is a complete, characterized and validated end to end restoration and optimization of Heathkit SB-200/201 RF linear amplifier. SB-200-restore-and-optimization-K7BIT.pdf Click here to view the article. |
Created: 31 Oct 2018 Heathkit HW-101 | |
Subject: Mod for Heathkit HW-101 | |
Improve Your HW101 Rig Loss of sensitivity Low transmitter output power VOX control hard to set Chirps on CW CW sidetone oscillator problems HW101MOD.pdf Click here to view the article. |
Created: 26 Mar 2018 Icom IC-7300 | |
Subject: ATU modification for Icom IC-7300 | |
Icom’s IC-7300 is an awesome rig, but unfortunately the impedance range that the built-in antenna tuner can match is rather narrow (comparing to other Icom radios). Hopefully this is easy to ch... Click here to view the article. |
Created: 23 Mar 2018 Icom IC-7000 | |
Subject: Hardware upgrade fan on Icom IC-7000 | |
OM wich owns IC7000 knows that the little jewel becomes hot with much use at maximum power. Personally I use 144,430 and hf, where @ 100w the problem is very strong. After about 1 minute in tx a... Click here to view the article. |
Created: 13 May 2018 Icom IC-E92 | |
Subject: Frequency expansion for ic-e92d | |
Edit frequency expansion icom ic-e92d. Desolder the diode D4 as shown in the figure below. Picture: modifica-ic-e92d.jpeg Click here to view the article. |
Created: 14 May 2018 Icom IC-9100 | |
Subject: Cross band repeater mod for IC-9100 | |
This is cross band repeater mods for IC-9100 Both VFO need to be on FM to go back, just unlock radio Download the complete article cross-band-repeater-IC-9100.pdf Click here to view the article. |
Created: 20 May 2018 Icom IC-7300 | |
Subject: Antenna tuner range mod for Icom IC-7300 | |
This modification consists of making the SWR detection circuit in the TUNER UNIT slightly less sensible. This modification DOES NOT affect the main SWR detection circuit on the PA unit that is respons... Click here to view the article. |
Created: 23 May 2018 Icom IC-765 | |
Subject: IC-765 degraded audio on USB LSB | |
Problem-with-USB-or-LSB-reception-in-Icom-ic-765.pdf Problem with USB or LSB reception in Icom ic 765 My team icom ic 765 a day after half an hour in reception I begin to notice that it does not rec... Click here to view the article. |
Created: 02 Jun 2018 Icom IC-7000 | |
Subject: Icom ic7000 SDR modification | |
Use your ic7000 transceiver as an SDR front end I've made this modification 4-5 years ago It uses a small sample of the last intermediate frequency of the ic7000 (16,150 KHz) directly to PC soun... Click here to view the article. |
Created: 08 Jun 2018 Icom IC-7610 | |
Subject: Mods Full tx ic7610 1.8- 30 / 50- 54 Mhz on IC-7610 | |
original mods ORIGINAL MATRICE REMOVE FULL TX 1.8 / 30 MHZ 50- 54 MHZ Click here to view the article. |
Created: 25 Jun 2018 Icom IC-R9000 | |
Subject: No SSB audio, and a frozen bandscope display on IC-R9000 | |
Recently I had an Icom IC-R9000 in for repair exhibiting a strange fault The symptoms included random startup conditions after a reset, with no ssb audio, and a frozen bandscope display. Ch... Click here to view the article. |
Created: 06 Jul 2018 Icom IC-R9000 | |
Subject: Cheap LCD replacement for the old CRT display on Icom IC-R9000 | |
The CRT displays in the early R9000 receives are now hard to come by, and very expensive when found. A very easy to install LCD version can be sourced from Allibaba at "VS Displays" store. Its descri... Click here to view the article. |
Created: 30 Jul 2018 Icom IC-230 | |
Subject: Pinout for 9 pin accessory jack on IC-230 | |
The Icom IC-230 features a 9 pin accessory jack on the right side of the radio, nearer to the front panel. There were two versions of the user manual; the version which included this pinou... Click here to view the article. |
Created: 23 Aug 2018 Icom IC-756PRO3 | |
Subject: Overheating and cuts out on IC-756PRO3 | |
Problems when using FT8 mode which caused the 756 to run hot and began to switch off, switching itself back on in a short time. Temperature which caused the problem (back panel heat probe) aroun... Click here to view the article. |
Created: 27 Aug 2018 Icom IC-703 | |
Subject: Improve filters blow-by on IC-703 | |
Just info regarding IC-703 PIN diodes replacement†You have to replace MA77 diodes with BAR64-03W (diodes D1303, D1305, D1307, D1309, D1311, D1313, D1315 and D1317) to improve strong... Click here to view the article. |
Created: 11 Oct 2018 Icom IC-7100 | |
Subject: AVG-Power IC-7100 von Andreas, DL6EAT | |
Dipl. .Ing Andreas Duessler, DL6EAT – W6EAT - 10. Oktober 2018 Einige Überlegungen zum Thema „mangelnde Aussteuerung&ldquo... Click here to view the article. |
Created: 04 Feb 2018 Kenwood MC-60 | |
Subject: Adding transmit L.E.D light on Kenwood MC-60 | |
To add a L.E.D transmit light to the MC-60 light is very helpful. If you use a MC-60 I know it is very easy to leave the lock button on by accident, leaving the radio keyed up. First open up ... Click here to view the article. |
Created: 15 Apr 2018 Kenwood TS-2000 | |
Subject: Extend RX down to 10 kHz on TS-2000 | |
Normally the Kenwood TS-2000 has a lowest tuned frequency of 30 kHz. There is a way to extend this down to 10 kHz, in order to receive the VLF signals that live in 'the basement&#... Click here to view the article. |
Created: 20 May 2018 Kenwood TS-820 | |
Subject: Antenna relay RL-1 equivalent and datasheet (pinout) on TS-830 | |
RL1 Antenna relay ts-820 I recovered a ts-820 with wiring modifications at this relay. It is impossible to find datasheet of this relay MH4P Omron ! There is also wrong informations on the net a... Click here to view the article. |
Created: 27 May 2018 Kenwood TS-830 | |
Subject: Improved screen grid supply for Kenwood TS-830S | |
A simple screen grid stabiliser to protect the 6146 valves and give better linearity for the Kenwood hybrid transceivers. Improving-the-Kenwood-TS.pdf Click here to view the article. |
Created: 13 Jul 2018 Kenwood TS-2000 | |
Subject: TS-2000 HF/VHF pre driver overheat modification – preventative maintenance | |
KENWOOD TS-2000 HF/VHF PRE DRIVER OVERHEAT MOD – PREVENTATIVE MAINTENANCE This is a minor modification for the TS-2000 from serial number B0xxx onwards which have the FET power output devices. .... Click here to view the article. |
Created: 17 Jul 2018 Kenwood TS-2000 | |
Subject: Mod Kenwood TS-2000 for use in DMR as MMDVM station | |
Of origin this rig does not accept correctly the signals DMR in TX, nevertheless if it works well for RX. This small modification allows you to use your TS-2000 as a DMO station in DMR digital radio w... Click here to view the article. |
Created: 19 Aug 2018 Kenwood TS-830 | |
Subject: Replacing weak HV Caps in the TS-830 | |
Here is a PDF with pictures showing the procedure for changing the HV filter caps in the Kenwood TS-830 radio. 830S-HV-Caps.pdf Click here to view the article. |
Created: 20 Oct 2018 Kenwood MC-58 | |
Subject: MC-58DM more mic gain!! | |
Getting more gain, for Kenwood;s MC-58DM microphone!!! Just change the R10, from 820ohms to 4.7kohms and that;s it!!!...The microphone gets all the rich modulation you need for a beautiful and strong... Click here to view the article. |
Created: 12 Feb 2018 Midland/Alan MISC | |
Subject: Wiring to radio - Packet Modem 1200 Baud on Alan rdm 1200 | |
Inside the Modem, with the frontside towards you, on the far right side in the corner you see 5 Solder points. From the COM port to the right counting five blobs, the wiring is : 1.) Modulatio... Click here to view the article. |
Created: 25 Aug 2018 Midland/Alan MISC | |
Subject: Mic Mod: Transmit Audio Improvement for Midland MicroMobile MXT115 | |
The transmit audio of the MicroMobile series radios can be improved by enlarging the hole for the electret mic element (circled in yellow) in the upper right corner of the microphone. What looks li... Click here to view the article. |
Created: 20 Oct 2018 Motorola PM-400 | |
Subject: Mod Software to allow 144 -146 Mhz on Motorola PM-400 in VHF Model | |
You must modify 2 files in the RSS using a hex editor. PM400.exe Line -0008DA24 from 74 to EB -0008DA3D from 75 to EB -001D7DD4 from 74 to EB -001D7DEF from 75 to EB -001DAA50 from 74 to EB -0... Click here to view the article. |
Created: 12 Mar 2018 Other MISC | |
Subject: Adding headphone output and front panel adjustable sidetone level to Logikey CMOS-4 Keyer | |
This modification adds a properly leveled headphone output as well as a front panel potentiometer to adjust the sidetone level for both speaker and headphones for a Logikey CMOS-4 keyer. It also impro... Click here to view the article. |
Created: 03 Mar 2018 Other MISC | |
Subject: Tram antenna 1191 Glass Mount antenna hint | |
Glass Mount Antenna Hint: About 20 years ago, I needed to mount a mobile VHF/UHF antenna on my vehicle in such a way that it would clear the parking garage entrance at work. I decided to try a Tram ... Click here to view the article. |
Created: 03 Mar 2018 Other MISC | |
Subject: Power output drops to 2 or 3 Volts on Astron SS-30 | |
After checking all components that normally fail and found none bad, I noticed the control pc board that mounts on the main board had some glue substance on the pins and a couple of resistors where it... Click here to view the article. |
Created: 11 Apr 2018 Other MISC | |
Subject: Squelch pop noise modification for Ailunce HD1 dual band DMR handheld | |
This modification is for the Ailunce HD1 dual band dmr handhelds to remove the annoying pop click sound just as the squelch opens. Dissassemble the radio by remove the 2 control knobs on the ra... Click here to view the article. |
Created: 05 Jun 2018 Other MISC | |
Subject: Sprocket replacement on Henry Radio 2020 | |
This is a common problem with these radios. Fortunately they are being reproduced...by NR6C...Just Search for his call ..... Use this procedure to replace cracked Uniden sprockets with reproduction A... Click here to view the article. |
Created: 09 Jul 2018 Other MISC | |
Subject: Replace stock antenna by BNC connector on Tecsun PL-365 | |
Replace stock antenna by BNC connector The Tecsun PL-365 is a great SW radio (as well as an FM radio) with both regular broadcast bands as well as HAM bands and selectable USB/LSB reception with BFO.... Click here to view the article. |
Created: 11 Jul 2018 Other MISC | |
Subject: Modification of Ameco PT-3 For 2nd Receiver Capibility | |
Download the complete article in PDF from Modification-of-PT-3-For-2nd-Receiver-Capibility.pdf Click here to view the article. |
Created: 12 Jul 2018 Other MISC | |
Subject: Fully functional USB_cable (Tested) for Baofeng UV-5R and UV-R5A | |
Fully functional USB cable (Tested) for Baofeng UV-5R and UV-R5A with logic level translator, because the Baofeng transceiver send 1.5v for logic level LOW. Picture: Fully-functional-USB-cable-Tested... Click here to view the article. |
Created: 16 Jul 2018 Other MISC | |
Subject: Simple TX power reduction from 100w PEP to 50w PEP can be set in NSP on CODAN NGT-SR | |
Open NSP v5.14 Open desired profile or read profile from radio From the toolbar select VIEW and the drop down option CONTROLS The editable settings on the CONTROLS tab are listed alphabetically. Scr... Click here to view the article. |
Created: 25 Jul 2018 Other MISC | |
Subject: Customized firmware and front panel for Barrett 950 | |
manuale01.pdf I modified the Barrett 950 rewriting my own firmware and building customized fronte panel.Documentati in (in Italian) in the PDF file. For more information write to max@malaroda.NET 7... Click here to view the article. |
Created: 17 Oct 2018 Other MISC | |
Subject: Watkins-Johnson WJ-8718 upgrading to MFP version | |
Paolo have prepared the first of two articles concerning practical instructions for upgrading a WJ-8718 Series receiver to the /MFP version. The first article is in two parts (Text and Figures)an... Click here to view the article. |
Created: 03 Nov 2018 Other MISC | |
Subject: Squelch for Spider manpack radio | |
The S.P.I.D.E.R. manpack radio by Holland Signaal is a great surplus radio but it lacks a normal RF squelch. This mod adds a squelch by detecting high-frequency noise in the audio and when the noise d... Click here to view the article. |
Created: 16 Feb 2018 Uniden BC-350 | |
Subject: Discrimminator coil adjustment for Uniden BC-350 | |
Showing Location of Discriminator coil adjust for best audio on WX channel. Correcting private scan problems (no stop on channel). Click here to view the article. |
Created: 15 Mar 2018 Yaesu FT-290 | |
Subject: Intermittant Tx-Rx Audio feedback from Mic when in RX on FT-290RII | |
Interesting fault developed on FT290 mk2. 1st Symptoms :- crackling on RX (SSB/CW) and intermittent loss of TX power Deterioration :- No Tx or Rx (any mode) Audio howl-round from Mic to speaker in Re... Click here to view the article. |
Created: 21 Mar 2018 Yaesu FT-7100 | |
Subject: Connection between Main Unit and Control Unit with very long Network Cable (Pinout&Adapter) | |
Documentation Adapter Cable for Yaesu FT-7100: Pinout RJ12 Main-Unit: Pin 1 – Modulation Pin 2 – Powerswitch Pin 3 – 9V Pin 4 – GND Pin 5 – RXD Control-Unit Main-Un... Click here to view the article. |
Created: 06 Feb 2018 Yaesu FT-2000 | |
Subject: Installing 4Khz Ceramic filter in FT-2000, second IF 450 kHz | |
In FT 2000 transceiver 450kHz Ceramic Filter CF 1001 has been build in second IF with a BW of about 15kHZ, because FT 2000 can be used in FM and also in AM mode. Therefore ... Click here to view the article. |
Created: 12 Feb 2018 Yaesu FT-7800 | |
Subject: Yaesu FT-7800 Extended TX & Tricks - Italian | |
Yaesu FT-7800 Modifica TX Programmazione Memorie , Menu segreti i6ibe Ivo Brugnera brugneraivo@alice.it Salve, rieccomi con una nuova modifica ad un apparato Yaesu, si tratta del duo-banda m... Click here to view the article. |
Created: 13 Feb 2018 Yaesu FT-25 | |
Subject: Serial Programming Cable for Yaesu FT-25 and FT-65 Radios | |
Components: MAX233 or MAX233A RS-232/TTL converter. DIP packaging pinout is shown on the diagram below. MAX233 does not require any external capacitors. You may use any other MAX220-MAX249 ch... Click here to view the article. |
Created: 22 Feb 2018 Yaesu FT-290 | |
Subject: YAESU FT-290 RII CTCSS for EU radios | |
When converting FT-290 RII (EU) radios from single tone to CTCSS, (2) jumpers inside the radio have to be changed.So the FTS-7 CTCSS board isn’t just a drop-in replacement for the originally ins... Click here to view the article. |
Created: 24 Feb 2018 Yaesu FT-891 | |
Subject: FT-891 Solderless HF Transmit Range expansion | |
Please follow instructions carefully on picture provided to complete the mod WITHOUT the need to use ay soldering. Click here to view the article. |
Created: 25 Feb 2018 Yaesu FT-840 | |
Subject: PAT50M board mod for FT-840 | |
Here is a pic getting power from L1019. I removed this point as it dosent power the board on transmit so you dont hear or see your audio in waterfall. Keeping the board powered allows for your transmi... Click here to view the article. |
Created: 26 Feb 2018 Yaesu FT-270 | |
Subject: Expanded TX/RX for NA market FT-270/FT-277 illustrated | |
Remove battery. Refer to illustration below for following steps. Remove self adhering black ACCY cover on lower chassis. Remove R1290. Re-install black ACCY cover. Re-attach battery. Radio... Click here to view the article. |
Created: 07 Mar 2018 Yaesu FRG-7 | |
Subject: KIWA Electronics audio mod kit (discontinued, company out of business) for Yaesu FRG-7 | |
Copied from the internet, the KIWA mod widened the audio output of the FRG-7, so AM listening was more enjoyable. The speaker and audio amp are limits on this, both by speaker response and amp p... Click here to view the article. |
Created: 09 Mar 2018 Yaesu FT-290 | |
Subject: FT290R: Output power drops after few seconds | |
When running at full power (like in FM mode, or when pressing the CW key for some time), output power dropped from 2.8 W to about 1.5 W. This was accompanied by the PA driver transistor (2SC2538) heat... Click here to view the article. |
Created: 10 Mar 2018 Yaesu FT-991 | |
Subject: Panadapter Mod For the FT991 both HF and VHF By KU0D | |
Panadapter For the FT991 By KU0D with G4HUP Panadapter Pat70 Board. Instructions in the PDFFT991-Installation.pdf Picture: 20748180-300977240369016-7509024657488764574-o.jpg Picture: 20819581-300977... Click here to view the article. |
Created: 26 Apr 2018 Yaesu FT-897 | |
Subject: Yaesu FT-857/897 fan noise in TX audio | |
This problem devloped with my 'rescue radio', the ft-897 in which I recently replaced the corroded crystal IF filters (see existing mods for this known problem). It is one of the batch that ... Click here to view the article. |
Created: 01 May 2018 Yaesu FT-980 | |
Subject: FT-980 Improved transmitter ALC compression and average output power | |
When transmitting on the FT-980 the ALC compresses speech on IF to keep maximum power and intelligibility at the correspondent's reception. To increase signal to noise of your received signal at ... Click here to view the article. |
Created: 01 May 2018 Yaesu FT-980 | |
Subject: FT-980 Transmission general coverage 2-30 MHz | |
This modification is based on a document (dated January 1994) by Ray Pesek WB8NXR. This new and easy modification brings several improvements regarding transmitter harmonics rejection. From 2 to 30 MH... Click here to view the article. |
Created: 04 Jun 2018 Yaesu FT-DX1200 | |
Subject: Interconnecting an amplifier on Yaesy FT-dx1200 | |
The TX ground out (pin 2) of the Linear Jack is a transistor "OPEN COLLECTOR" circuit. It is capable of handling positive relay coil voltages up to +30VDC @ 500ma. DO NOT exceed the maximum ... Click here to view the article. |
Created: 03 Aug 2018 Yaesu FRG-8800 | |
Subject: FRG-8800 erratic tuning | |
The Yaesu FRG8800 is now showing signs of old age, recently two examples have turned up on the bench with similar strange faults. The symptom shows as a loud click in the audio every 100 Hz when tunin... Click here to view the article. |
Created: 05 Sep 2018 Yaesu FT-2800 | |
Subject: "User Port" demystified; menu switchable hardware pin on FT-2800M | |
Most of the Yaesu rigs have some "easter eggs", and so also the FT-2800M. There's a service connector J309 on the mainboard for some "future options". Pins 3 and 4 are linked by a 0 Ohm resistor ... Click here to view the article. |
Created: 12 Sep 2018 Yaesu FT-8900 | |
Subject: Head extention on Yaesu FT-8900 | |
Been done before, I know. I had reason to 'knock up' another set of head extention cables to use on existing Cat5 infrastructure so what I needed was a cable with RJ12 to go into the r... Click here to view the article. |
Created: 25 Sep 2018 Yaesu FT-991 | |
Subject: FT-991: Prevention of blown finals and infinite SWR after tuning cure. | |
There have been published a number of issues with users stating their FT-991 is blowing finals. Yaesu have diligently replaced these, only to have some users [as claimed on various forums] send the sa... Click here to view the article. |
Created: 10 Oct 2018 Yaesu FT-1000MP | |
Subject: FT1000-MP / FT1000-MK5: an effective panadapter by F5LOL | |
The YAESU FT1000-MP or MK5 have nice receivers but without possibility to monitor a whole band directly on the screen as the new SDR transceivers. Before writing this paper, I tried a lot of SDR... Click here to view the article. |
Created: 19 Oct 2018 Yaesu FT-4 | |
Subject: Yaesu FT4X Wideband Modification | |
Switch on Radio with PTT and T/Call Pressed. Enters Menu Mode EU & USA version enter the code 32406665 on the keypad After the 5 is entered the radio resets Nothing will show in the display wh... Click here to view the article. |
Created: 22 Oct 2018 Yaesu MH-29 | |
Subject: Yaesu MH-29 Display Microphone Operating Instructions | |
October 11 2018 by KI4RK The microphone came with a sheet of paper fort instructions. It basically tells how to program the User Button for your choice of functions. The microphone has four b... Click here to view the article. |
Created: 03 Apr 2018 Antenna HF | |
Subject: OCF 10 thru 80M antenna | |
This Antenna works great. Easy to build, Low angle for some great DX. If fed with open wire. this antenna will work on 160M 73 de N9OVROCFAntenna.pdf Click here to view the article. |
Created: 25 Aug 2018 Power supply 12-VOLT | |
Subject: Strong powersupply for 12 Voltage | |
The PS (power supply) was made in several different versions and multiple units. I will try to explain how it works. Generally in all PSs the base transistor (one or more) is supplied by curent thro... Click here to view the article. |
Created: 03 Apr 2018 Transceiver MISC | |
Subject: Fan Timer for Repeaters | |
Circuit Description This circuit differs from one I previously wrote (Temperature Controlled Fan Switch, 2011-05-19) in that it does not monitor temperature to initiate the fan – instead this c... Click here to view the article. |
Created: 29 Apr 2018 Transceiver MISC | |
Subject: Yaesu FT-8100, S# 7K070372; Yaesu FT-920, S# 7F020059; Manufacturer’s Claimed Specifications | |
Yaesu FT-920 MF/HF/6 Meter Transceiver Yaesu FT-920, serial number 7F020059 Yaesu-FT-9020.pdf Yaesu FT-8100R Dual-Band FM Mobile Transceivers Yaesu FT-8100, serial number 7K070372 Yaesu-FT-8100R... Click here to view the article. |
Created: 11 May 2018 Transceiver MISC | |
Subject: Free mic bracket with gum | |
While out shopping with Mrs G6 at the checkout I noticed tubs of Wrigley chewing gum but what really caught my eye was the free bracket to attach the tub to a cars air vent. It looked... Click here to view the article. |
Created: 22 Jul 2018 Transceiver MISC | |
Subject: Low cost desk microphone | |
Requiring a desk microphone to use with uBitx transceiver rather than use the bare element and switch supplied I scoured the ads on a well-known auction site and for £1.99 plus postage pur... Click here to view the article. |
Note, sometimes it can be difficult to see the changes since the update can be a little correct in the text, but sometime the update can be a new picture to the existing article.
Updated: 28 Sep 2018 Icom IC-970 | |
Subject: IC-970 /970h mod | |
Several OM wrote to me following the first ??????MOD?????? it was not very clear!!! (The goal of this modification was to be able to use the head of reception 136/174 MHz to connect a converter or a t... Click here to view the article. |
Updated: 03 Feb 2018 Kenwood TS-590 | |
Subject: TS-590s ARCP issues with W10 | |
Enclosed a nice help for all TS-590S owners struggling with W10 ARCP-issues-with-TS-590-and-W10-solved.pdf Click here to view the article. |
Updated: 22 Oct 2018 Yaesu MH-29 | |
Subject: YAESU micro-phone MH-29A2B Test mode | |
Hello! Just wanted to let everyone know about a test mode I found on the yaesu remote mic (MH-29A2B). This test mode does all of the following: Lites the mic's backlight Flashes the busy/tx lite ... Click here to view the article. |
Below you will find some og the newest manual that we have received in the last few months. To download the manuals, just click direct on the link.
Regarding your Subscription !
If you do not wish to receive this newsletter any more, then you can unsubscribe from it, by going to https://www.mods.dk and scroll down to the newsletter field. Enter your mail address and click on the removal button. You will then receive a message that confirms you have been unsubscribed.
Best regards
mods.dk
© Copyright mods.dk 1996 - 2018